– Real Time: to display torque transition
– Peak Mode: to capture the peak torque achieved during a test
– on the display
– for data transfer to PC
– for printing with report
Special features of model HTGA in comparison to standard unit HTGS:
Torque meter with separate sensor for measuring the torque of screws, components, screw and plug connectors, drive shafts etc.
Hand-held unit for mains and battery operation with output signal and memory
Torque meter with digital output signal for data processing with a PC
Special features of model HTGA in comparison to standard unit HTGS:
Model | Model | Measuring Range | Resolution |
HTGS-0.5N | HTGA-0.5N | 0 – 50.00 Ncm | 0.01 Ncm |
HTGS-2N | HTGA-2N | 0 – 2.000 Nm (200 Ncm) | 0.001 Nm (0.1 Ncm) |
HTGS-5N | HTGA-5N | 0 – 5.000 Nm (500 Ncm) | 0.001 Nm (0.1 Ncm) |
HTGS-10N | HTGA-10N | 0 – 10.00 Nm (1000 Ncm) | 0.01 Nm (1 Ncm) |
Delivery includes no sensor attachment!
Accuracy: | ±0.5 % full scale ±1 digit |
Measuring frequency: | 2000 times/sec |
Selectable units: | Nm, Ncm, kgfm, kgfcm, Lbf.in, and ozf.in |
Display: | OLED, 4 digit, 14 mm high |
Overload capacity: | Approx. 200 % full scale, flashing display beyond 110 % full scale |
Display update: | 16 times/sec |
Memory: | Internal memory for max. 1000 values (clockwise or counter clockwise torque and peak values) |
Setpoints: | MIN (-NG), MAX (+NG) programmable, with output signal |
Output signal: | USB RS-232 (8, 1, N, 19200) analog ±2 V DC Open Collector-Comperator 3 x (+NG, Ok, -NG) overload signal |
Temperature range: | 0 – 40 °C |
Air humidity: | 80 % RH, max. |
Power supply: | Rechargeable NiMH batteries (approx. 6.5 hours continuous use, approx. 2 h charging time) and/or 100 – 240 V AC adapter and two adapters(EU/USA) |
Dimensions: | Display unit: 187 x 75 x 34 mm (LxWxH) Sensor: 183 x 39 mm (LxØ) |
Weight: (approx.): | Display unit: 490 g / sensor: 530 g (without pin chuck) complete set 2000 g |
Additional functions of HTGA in comparison to standard torque meter HTGS: | |
Torque-angle-measurement: | In combination with a test stand with linear scale torque-angle-measurements are possible |
Memory: | Readings can be transferred from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/sec) |
High low output: | 2 high/low output values can be set; If the reading reaches one of the output values, data will be sent to external devices (e.g. PC, printer) for data recording |
Extended peak mode: | Indication of two peak values per measurement |
Specifications subject to change without notice!
Ø 0.5 to 6.5 mm (not available for torque meter HTGS and HTGA with 0.5 Nm nominal load)
Order number: HT-DC-6.5
Ø 0.5 to 6.5 mm, stainless steel (not available for torque meter HTGS and HTGA with 0.5 Nm nominal load)
Order number: HT-DC-6.5SUS
Ø 1.2 to 13 mm (not available for torque meter HTGS and HTGA with 0.5 and 2 N nominal load)
Order number: HT-DC-13
Ø 0.5 mm up to 4 mm (not available for torque meter HTGS and HTGA with 10 Nm nominal load)
Order number: HT-DC-4
3/8″ square drive male (not available for torque meter HTGS and HTGA with 0.5 Nm nominal load)
Order number: HT-9.5SQ
1/4″ female square drive with 3 Pins (Phillips No. 1, No. 2 and screw blade 6.3 mm) – not available for torque meter HTGS and HTGA with 0.5 Nm nominal load
Order number: HT-DBH
M10 male thread (not available for torque meter HTGS and HTGA with 0.5 Nm nominal load)
Order number: HT-AD-M10
Only for HTGS-2N, HTGS-5N, HTGA-2N and HTGA-5N
For samples with Ø of 7 up to 50 mm.
Inclusive table pins (ST-P) with urethane surface, length 10 mm.
Recommended for locks, containers for eye drops, etc.
Order number: HT-ST
Only for HTGS-2N, HTGS-5N, HTGA-2N and HTGA-5N
For samples with Ø from 7 up to 50 mm.
Includes table pins (ST-01P) from stainless steel V2A, corrugated surface, length 10 mm.
Recommended for electronic components, plugs, etc.
Order number: HT-ST-01
Only for HTGS-2N, HTGS-5N, HTGA-2N and HTGA-5N
For samples with Ø from 7 up to 50 mm.
Includes table pins (ST-02P) with urethane surface, length 30 mm.
Recommended for cosmetics boxes, door knobs, lamps, etc.
Order number: HT-ST-02
Only for HTGS-2N, HTGS-5N, HTGA-2N and HTGA-5N
For samples with Ø from 10 up to 100 mm.
Includes table pins (ST-P) with urethane surface, length 10 mm.
Order number: HT-STW
Only for HTGS-2N, HTGS-5N, HTGA-2N and HTGA-5N
For samples with Ø from 10 up to 100 mm.
Includes table pins (ST-01P) from stainless steel V2A, corrugated surface, length 10 mm.
Order number: HT-STW-01
Only for HTGS-2N, HTGS-5N, HTGA-2N and HTGA-5N
For samples with Ø from 7 up to 50 mm.
Includes table pins (ST-02P) with urethane surface, length 30 mm.
Order number: HT-STW-02
Only for HTGS-0.5N, HTGS-2N, HTGA-0.5N and HTGA-2N
For samples with Ø from 7 up to 50 mm.
Includes table pins (ST-P) with urethane surface, length 10 mm.
Recommended for plastic tubes, etc.
Order number: HT-STL
Only for HTGS-0.5N, HTGS-2N, HTGA-0.5N and HTGA-2N
For samples with Ø from 7 up to 50 mm.
Includes table pins (ST-01P) from stainless steel V2A, corrugated surface, length 10 mm.
Recommended for motors, etc.
Order number: HT-STL-01
Only for HTGS-0.5N, HTGS-2N, HTGA-0.5N and HTGA-2N
For samples with Ø from 7 up to 50 mm.
Includes table pins (ST-02P) with urethane surface, length 30 mm.
Recommended for cosmetic containers, etc.
Order number: HT-STL-02
Only for HTGS-0.5N, HTGS-2N, HTGA-0.5N and HTGA-2N
For samples with Ø from 10 up to 100 mm.
Includes table pins (ST-P) with urethane surface, length 10 mm.
Recommended for volume dials, etc.
Order number: HT-STLW
Only for HTGS-0.5N, HTGS-2N, HTGA-0.5N and HTGA-2N
For samples with Ø from 10 up to 100 mm.
Includes table pins (ST-01P) from stainless steel V2A, corrugated surface, length 10 mm.
Recommended for motors, etc.
Order number: HT-STLW-01
Only for HTGS-0.5N, HTGS-2N, HTGA-0.5N and HTGA-2N
For samples with Ø from 7 up to 50 mm.
Includes table pins (ST-02P) with urethane surface, length 30 mm.
Recommended for bottle shaped containers, etc.
Order number: HT-STLW-02
USB cable approx. 1.5 m long, CD-ROM with USB-driver and software “Force-Logger” for data transfer
AC-adapter for 100 – 240 V AC
Order number: ADW-6010
Delivery includes a manufacturers inspection certificate free of charge.
Software for data acquisition by USB output
– Force-time graph
– Force gauge function setting
– Data storage as CSV file
Requirements: Microsoft Windows 8.1/10/11
Order number: SW-21
Additional functions in comparison to Force Recorder Light:
5 graphs at maximum can be displayed in a table
Requirements: Microsoft Windows 8.1/10/11
Order number: SW-22
Additional function in comparison to Force Recorder Light
– 5 graphs at maximum can be displayed in a table
– Force-displacement graphing (possible only in combination with a test stand with linear
scale)
Requirements: Microsoft Windows 8.1/10/11
Order number: SW-23
Software for Data acquisition by USB output:
– 10 graphs at maximum can be displayed in a table
– data acquisition of 4 force gauges simultaneously
– force gauge function setting
– data storage as CSV file
Requirements: Microsoft Windows 8.1/10/11
Order number: SW-26
Software for Data acquisition by USB output:
– data acquisition of 4 force gauges simultaneously
– force gauge function setting
– data storage as CSV file
Requirements: Microsoft Windows 8.1/10/11
Order number: SW-13
1 set (4 pieces), 10 mm long with urethane surface for the small table.
Recommended for locks, containers for eye drops, etc.
Order number: ST-P
1 set (4 pieces), 10 mm long from stainless steel for the small table.
Recommended for electronic components, plugs, etc.
Order number: ST-01P
1 set (4 pieces), 30 mm long with urethane surface for the small table.
Recommended for cosmetics boxes, door knobs, lamps, etc.
Order number: ST-02P
For fixing the sensor horizontal or vertical (for torque meter HTGS and HTGA up to max. 5 Nm).
Weight 1.100 g
Order number: SHT-5N
Nickel metal hydride accumulator, 2-pole connector
3.6 V, 1300 mAh
Order number: 40018I
For analog output, for connection to a line recorder.
Length approx. 3 m
Order number: CB-108
For RS-232 output with sub D 9 female, for connection to PC.
Length approx. 3 m
Order number: CB-208
For trigger input (input signal from an external device e. g. electronic switch to stop the measurement)
Order number: CB-808
With open ends (37-pin) for all available output signals to connect an unique device.
Order number: CB-908