Tension Sensor FSB1-422

8 Tension ranges available
from 0 - 100 cN up to 0 - 20 daN

Stationary electronic tension sensor for measuring low tensions of textile ribbons, films, foils, fibre bunches etc.

Cylindrical tape rollers with up to max. 30 mm width, one-sided mounting

Tension sensor with RS-422 output for multi station system and connection to a with PC

Categories: Tension Meter, FS-422 Series, Multi-Networking Sensors, Stationary, electronic

Print page

Special Features

Tension sensor FS1-422 with integrated microprocessor controlled measuring amplifier and RS-422 interface for multi station system

Various roller widths from 7 mm up to 30 mm according to the application are available. The roller width must correspond with the width of the material to be measured

Easy installation, even afterwards, on existing machines

2 Mounting possibilities: housing mounting or cylindrical hole mounting (mounting cut out: long hole R 19 mm, length 54 mm)

Easy calibration to customized material by operator – zero and gain calibration is required

Measuring principle – load cell with high quality strain gauge bridge

Tension sensor with mechanical overload protection

Standard Features

Tape rollers, ball-bearing mounted

Control lamp shows operative mode availability

Tension sensor FSB1-422 with aluminium housing

CAT 5 cables are used for data transfer

Required power supply +15…24 V DC (regulated)

Certificate of Compliance with the order 2.1 according EN 10204 is included

Optionally available: Inspection Certificate 3.1 according EN 10204 with calibration report

Special features of the RS-422 interface:

Up to 24 sensors with different tension ranges and designs may be connected in one line (data transfer max. 200 readings/sec.)
Connection to RS-232 using a converter (RS-422 – RS-232).
The RS-422 signal can be used for a single sensor over a distance of 1000 m.
Each sensor can individually be addressed and set up
Can be connected to PLC controls with digital input
Simple connection to BUS-Systems using gateways

Lern more about the different tension measuring systems

You are not sure, which system is right for, or where the differences are? Here we explain it for you.

Info tension measuring system

Available Models

Model	Tension Range*	Measuring Head Width**	Roller Width
FSB1-100-422	0 – 100 cN	60 mm	7, 10, 15, 20 mm
FSB1-200-422	0 – 200 cN	60 mm	7, 10, 15, 20 mm
FSB1-500-422	0 – 500 cN	60 mm	7, 10, 15, 20 mm
FSB1-1000-422	0 – 1000 cN	60 mm	7, 10, 15, 20, 30 mm
FSB1-2000-422	0 – 2000 cN	120 mm	7, 10, 15, 20, 30 mm
FSB1-5000-422	0 – 5000 cN	120 mm	7, 10, 15, 20, 30 mm
FSB1-10K-422	0 – 10 daN	120 mm	7, 10, 15, 20 mm
FSB1-20K-422	0 – 20 daN	220 mm	7, 10, 15, 20 mm

Other tension ranges available on request.
Other measuring units available, such as g or kg
* SCHMIDT calibration material depending on tension range and roller width
** Outside dimensions of front plate

Important for your order:
Please specify model and roller width! Small dual-flanged outer guide rollers are standard. All 3 rollers can be equipped with one flange, if the material to be measured is wider than the rollers. Please request when you order.

Calibration to customized material:
If process material differs significantly from the SCHMIDT calibration material in diameter, rigidity or shape, special calibration using customer supplied samples is recommended. For this purpose a material sample of about 5 m should be supplied.

For the tension sensor FSB1-422 we offer different display units for one or more sensors, as well as strain gauge amplifier.

Find further information at display units and amplifier

Tension sensor FSB1-422 can be reconverted for special applications.

Find further information at special design

Specifications

Calibration:	According to SCHMIDT factory procedure
Accuracy:	±1 % full scale and ±1 digit or better Other calibration material: ±3 % full scale and ±1 digit or better
Overload protection:	100 % of tension range
Measuring principle:	Strain gauge bridge
Measuring roller deflection:	Max. 0.5 mm
Natural frequency:	Approx. 500 Hz, depending on tension range
Signal processing:	Digital 12-bit A/D converter, internal averaging up to 4 sec
Communication frequency:	200 readings/sec
Temperature drift:	Less than ±0.05 % full scale/°C
Output signal:	RS-422 (57600, 8, N, 1)
Temperature range:	10 – 45 ºC
Air humidity:	85 % RH, max.
Power supply:	+15…24 V DC, 50 mA (regulated)
Housing material:	Aluminium
Dimensions:	See dimensions
Weight net (gross):	Up to model FSB1-1000-422 approx. 350 g (450 g) Model FSB1-2000-422 up to FSB1-10K-422 approx. 400 g (500 g) Model FSB1-20K-422 approx. 470 g (630 g)

Specifications subject to change without notice!

Tape Rollers

Roller Width	Line Speed v_max. … m/min>	Roller Material*
7 mm	1000	Hard-coated aluminium
10 mm	1000	Hard-coated aluminium
15 mm	1000	Hard-coated aluminium
20 mm	1000	Hard-coated aluminium
30 mm	1000	Hard-coated aluminium

*Other roller materials (nickel-plated steel or plastic), as well as special coatings (Code CF – for carbon fibre, NA optimized, Code KE – ceramic, Code AH – anti adhesive ) are available on request..

Accessories (optional)

Software Tension Inspect 3
Tension Inspect 3 Info (PDF)
For displaying and saving readings on a PC (Windows 7 and higher; 32 Bit und 64 Bit).
Features:
– Real-time reading
– The readings are also shown in a X-Y- diagram (time/date-tension)
– For data analysing the buffered diagram can be zoomed and scaled
– Recording of the buffered readings as CSV-file (on user request)
– Download of values to Excel
Software for 4, 8, 12, 16 or 24 sensors are available.

EBG800 - Serial Port Converter
Converter from RS-422 to RS-232 with terminal strip.
Order number: EBG800

EK0715 - Connecting Cable Cat 5 with open ends
Cat 5 cable with open ends for RS-422/RS-232 converter and power supply the last sensor. Length 3 m.
Order number: EK0715