Tension Meter DTSL

6 Tension ranges available
from 150 - 2500 cN up to 6 - 60 daN

Electronic tension meter for cables, ropes, wires, buffer tubes, fibre strands etc. up to 15 mm Ø, as well as flat material up to 10 mm width

Large, hardened guide rollers for minimized material deflection

Tension meter with many functions as turnable display, thickness compensation and possibility of custom made calibrations

Categories: Tension Meter, Hand-Held, electronic, DT Series

Print page

Special Features

Ball-bearing mounted guide rollers
– V-grooved (for material with max. 4 mm Ø)
– U-grooved (for material with 3 up to 15 mm Ø)
– tape grooved (for material with max. width of 10 mm)

Large roller diameter for minimized material deflection

Special guides on the bracket assembly permit easy material acquisition

Tension meter DTSL with large, colour TFT display

3 different display modes:
– numeric
– numeric with bargraph
– numeric with graph (Time-Tension)

The display rotates in 90° steps for better reading

New, unique, force reduced material catching system

Automatic „Zero-Setting“ in each measuring position using a special sensor technique

1 factory adjustment, as well as 4 material memory locations for customer made calibrations

Calibration adjustment for fine tuning of the calibration if material differs from the used calibration material

Programmable MIN- and MAX alarms: indication in the display, if reading is out of limits

The MIN and MAX reading will be shown in the Display for the adjusted time window (2 – 60 seconds).

High speed data sampling (internal 8 kHz) and recording of MIN-, MAX-, last reading, average and standard deviation

Selectable units of measurement: cN, daN, g, kg, N, lb

Menu set-up in English or German language

Flexible menu set-up to meet operators demand

Some functions can be password protected

Note: Tension meter DTXL offers additional features, like interface, statistical evaluation on PC and a large internal memory.

Standard Features

Everything in operator’s view:
– the guide rollers
– the measured material
– the readings

Filament guide and roller shifting mechanism ensure easy acquisition of the running material

Rubberized handle provides a secure hold in the operators‘ hand

Tension meter DTSL with rugged aluminium housing

LiPo accumulator (approx. 30 hours continuous operation) with AC adapter

CE certified, interference resistant against static electrifications

Certificate of Compliance with the order 2.1 according EN 10204 is included

Optionally available: Inspection Certificate 3.1 according EN 10204 with calibration report

BMWi Logo

Available Models

Model	Measuring Range	Resolution	Measuring Head Width*	SCHMIDT Calibration Material
DTSL-2500	150 – 2500 cN	1 cN	185 mm	With convenient material for each roller design or customer supplied material
DTSL-5000	250 – 5000 cN	1 cN	185 mm	With convenient material for each roller design or customer supplied material
DTSL-10K	1 – 10 daN	0.01 daN	235 mm	With convenient material for each roller design or customer supplied material
DTSL-20K	2 – 20 daN	0.01 daN	235 mm	With convenient material for each roller design or customer supplied material
DTSL-50K-R4	5 – 50 daN	0.01 daN	226 mm	With convenient or customer supplied material
DTSL-50K-R5	5 – 50 daN	0.01 daN	226 mm	With convenient or customer supplied material
DTSL-60K-R4	6 – 60 daN	0.01 daN	276 mm	With convenient or customer supplied material
DTSL-60K-R5	6 – 60 daN	0.01 daN	276 mm	With convenient or customer supplied material

* Outer distance between outside guide rollers

Tension Meter DTSL can be reconverted for special applications.

Find further information at special design

Specifications

Calibration:	According SCHMIDT factory procedure
Accuracy:	From 5 % up to 100 % full scale: ± 3 % full scale and ± 1 digit Remaining range, device with tension range 50 daN and 60 daN and customer supplied materials: ±5 % full scale and ±1 digit
Memory for material curves:	1 for SCHMIDT calibration plus 4 for customized calibrations
Measuring units:	Force (switchable): cN, daN, g, kg, N, lb Thickness (switchable): mm, inch
Overrange:	Approx. 10 % full scale, without accuracy guarantee
Overload protection:	100 % full scale
Measuring principle:	Strain gauge bridge
Signal processing:	Digital, 16 bit A/D converter
Measuring frequency:	Max. 1 kHz (1000 measurings/sec), intern 8 kHz
Measuring roller deflection:	Max. 0.2 mm
Display:	Colour TFT display
3 different displays:	Numeric Numeric with graph (time-tension) X-Y-diagram
Display update rate:	Approx. 2 times per second
Memory:	MIN, MAX, AVG, standard deviation and LAST
Damping:	Adjustable electronic damping (averaging)
Cal. Adjustment:	± 10 steps in 1 % increment
Thickness compensation:	Max. 2.5 mm (not available for all models)
Auto power off:	Approx. 3 minutes of non-use
Temperature coefficient:	Gain: less than ± 0.01 % full scale /°C
Zero point:	Less than ± 0.03 % full scale /°C
Temperature range:	10 – 45 °C
Air humidity:	85 % RH, max.
Power supply:	LiPo accumulator (approx. 30 h continuous use), charging time approx. 3 1/2 h, USB AC adapter 100 – 240 V AC with 4 adapters (EU/USA/UK/AUS-NZ)
Housing material:	Die-cast aluminium
Housing dimensions:	See Dimensions
Weight, net (gross):	Approx. 940 g (1620 g)

Specifications subject to change without notice!

Guide Rollers

Order-Code	Line Speed v_max.… m/min	Roller Material
Standard	4000	Stainless steel 1.4125 (max. Ø 4mm)
Code R1	4000	Hard chrome-plated steel (radius R5), for material diameter 3 – 9 mm
Code R4	1000	Hardened steel (radius R8), for material diameter 8 – 11 mm
Code R5	1000	Hardened steel (radius R8), for material diameter 12 – 15 mm
Code B6	2000	Hardened steel, width 6 mm
Code B10	2000	Hardened steel, width 10 mm

Standard Accessories

K50202 - USB AC Adapter
USB AC adapter with 4 adapters (EU/USA/UK/AUS-NZ) for 100 – 240 V AC and USB cable for loading the accumulator
Order number: K50202

Attachment

Code MH - Online Mounting
To mount the gauge for online use, the housing can be equipped with mounting threads. There are to bolts with M5 female thread on the rear side. This feature cannot be installed afterwords.

Calibration Report

Inspection Certificate 3.1 according DIN EN 10204
including a calibration report is optional available.

Inspection Certificate 3.1 (PDF)

Spare Rollers

Download an overview for the guide rollers:

Guide Roller Catalogue (PDF)

Dimensions

Dimensions of tension meter DTSL for download:

Drawing (PDF)

Delivery Includes

Tension meter DTSL with carrying case, accumulator and USB AC adapter with 4 adapters (EU/USA/UK/AUS-NZ), Certificate of compliance with the order 2.1 according EN 10204 free of charge, operating instruction in German or English (as requested)

How To Order

To order tension meter DTSL:

Please indicate the complete order number e. g.:

Model with tension range		Code for guide rollers (if not standard)		Code attachment		Complete Order No.
DTSL-5000	+	B6	+	MH	=	DTSL-5000-B6-MH

Instruction Manual

Download the instruction manual for tension meter DTSL:

Instruction Manual (PDF)

If you want to get a quote or want to place an order please contact us.

+49 (0)8638 9410-0

+49 (0)8638 4825

[email protected]

Print page

Infos

Infos

Infos

Infos

Infos