Motorized Torque Stand MTS

Measuring range 0 - 2.000 Nm, 5.000 Nm or 10.00 Nm
Resolution depending the range 0.001 Nm or 0.01 Nm

Motorized test stand for determining and testing the opening and closing forces of screw caps, used for bottles, cans, cosmetic products etc. Further application areas are testing torque switches, plugs, lenses etc. The most importend sectors of industry are the pharmaceutical, cosmetics,  beverage and electronic industry,
Torque stand assures constant, identical measuring conditions

Special Features Torque Stand

  • The motorized torque test stand can be configurated according the customers demand. The torque stand exists out of a test stand depending the sample height, a torque meter with different ranges and features as well as a upper chuck and lower table .
  • The torque will be measured without influence by the operator. The results are more accurate and significante as measured with a manual device.
  • 3 operation modes:
    Normal: Revolution occurs in the selected direction, until the stop-switch will be pressed
    +NG Stop: Revolution occurs in one direction, until the adjusted value is reached
    Endurance Test: Repeats the operation in two directions (open - close), within the adjusted limits (MTS series). The number of repeats are shown in the display. The opening and closing angel, as well as the number of repeats can be adjusted with MTS-RA series
display torque meter MTS The following information are shown in the display

  • Rotational speed e. g. 51.5 /sec
  • Status of the instrument
  • Operation mode
  • Counter for endurance test
  • Max. size of samples:
    - upper clamping chuck  20 - 90 mm or 7 - 50 mm
    - lower clamping table 20 - 160 mm or 7 - 50 mm
    - Max. available sample height 140, 240 mm or 340 mm
  • The rotation speed can continuousely be adjusted 3 - 90 degree/sec. The value will be displayed.

Special Features torque meter

  • 2 Display Modes:
    Real Time -
    displays the actual torque
    Peak Force - to measure and save the peak torque
  • Display the opening or closeing torque (clockwise and counter clockwise torque)
  • 3 selectable units: Nm, kgfm, Lbf.in or Ncm, kgfcm, ozf.in
  • Programmable high/low setpoints for go/no-go testing with color-coded indicators (orange, green, red) in the LED display
  • Torque meter with high internal sampling rate of 2000 times/sec to capture peak values.
  • Storage of 1000 values for recall:
    - On the display
    - For data transfer to a PC
    - For printing with report
  • 4 output signals: USB, RS232, analog, and Mitutoyo Digimatic
  • Display update time 10 times/sec
  • Easy to read display (OLED) for Real Time or Peak value including units. Depending to the series additional information are displayed as e. g. memory, number of go testings, limits, 1st and 2nd peak values etc.
Display torque meter DTXA
Special features of model DTXA in comparison to the standard model DTXS
  • Indication of 1st and 2nd peak value per measurement, e. g. closure with predetermined break point
  • Readings can be transfered from the internal memory to an USB flash drive or directly saved on it (sampling rate 100 times/sec)
  • 2 comperator values can be set; If the reading reaches one of the output values, data will be sent to external devices (e.g. PC, printer) for data recording 
Special features of model MTS-RA in combination with the torque meter DTXA in comparison with the standard model MTS with the torque meter DTXS
  • Force-angle measurements are possible. The software "Force Recorder Professional" is additionaly required

Standard Features

  • Torque measuring unit for fast, accurate measuring
  • High repeatability
  • Easy to use
  • Inclusive 30 days trial version of Software Force Recorder Professional
  • Manufacturer`s certificate with measured values is included


For further information, please open
the original PDF from the manufacturer.

Required Moduls

Torque Stand

Available with standard features or with code RA (Necessary for force-angle measurements). Sample Height up to 340 mm
Torque Meter

Available as standard model DTXS or DTXS-Z, as well as torque meter DTXA or DTXA-Z with additional funcitions (Necessary for force-angle measurements).
The models DTXS and DTXA will be delivered with standard table, while type Z has no clamping device.
Lower Clamping Table

The lower clamping device has to be mounted at the torque meter. It can be selected between a large or a small clamping table, as well as a torque pin chuck. The clamping tables are available with different table pins.
Upper Clamping Chuck

The upper clamping device has to be mounted at the torque stand. It can be selected between a large or a small clamping chuck, as well as a torque pin chuck or an adapter with M10 male thread. The small clamping chuck is available with different table pins.
Software

The software "Force Recorder" is required for data aquisition by USB output. 3 versions are available, in which "Force Recorder Professional" is necessary for force-angle measurements.

Available Torque Stands

ModelMax. Sample HeightDescription
MTS-10N140 mm
MTS-10N-L240 mm
MTS-10N-2L340 mm
MTS-10N-RA140 mmwith rotary encoder
MTS-10N-L-RA240 mmwith rotary encoder
MTS-10N-2L-RA340 mmwith rotary encoder

Available Models - Standard Model*

ModelModelMeasuring rangeResolution
DTXS-2NDTXA-2N0 - 2.000 Nm (200 Ncm)0.001 Nm (0.1 Ncm)
DTXS-5NDTXA-5N0 - 5.000 Nm (500 Ncm)0.001 Nm (0.1 Ncm)
DTXS-10NDTXA-10N0 - 10.00 Nm (1000 Ncm)0.01 Nm (1 Ncm)
*inclusive table DT-TB

Available Models - self configurated

ModelModelDescription
DTXS-2N-ZDTXA-2N-Zwithout table
DTXS-5N-ZDTXA-5N-Zwithout table
DTXS-10N-ZDTXA-10N-Zwithout table

Lower Clamping Table

Table

For samples with from 20 up to 160 mm.
Includes table pins (TB-P) with urethane surface, length 25 mm.
Recommended for PET bottles, cans etc.
Order number: DT-TB

Click picture for more information

Table

For samples with from 20 up to 160 mm.
Includes table pins (TB-01P) from stainless steel V2A, corrugated surface, length 26 mm.
Recommended for aluminium cans, hard plastic containers etc.
Order number: DT-TB-01

Click picture for more information

Table

For samples with from 20 up to 160 mm.
Includes table pins (TB-02P) with urethane surface, length 70 mm.
Recommended for conductor plates, lens of cameras, large bottles, etc.
Order number: DT-TB-02

Click picture for more information

Small Table

For samples with from 7 up to 50 mm (for max. 5 Nm nominal load).
Includes table pins (ST-P) with urethane surface, length 10 mm.
Recommended for locks, containers for eye drops, etc.
Order number: DT-ST

Click picture for more information

Small Table

For samples with from 7 up to 50 mm (for max. 5 Nm nominal load).
Includes table pins (ST-01P) from stainless steel V2A, corrugated surface, length 10 mm.
Recommended for electronic components, plugs, etc.
Order number: DT-ST-01

Click picture for more information

Small Table

For samples with from 7 up to 50 mm. (for max. 5 Nm nominal load).
Includes table pins (ST-02P) with urethane surface, length 30 mm.
Recommended for cosmetics boxes, door knobs, lamps, etc.
Order number: DT-ST-02

Click picture for more information

Torque Pin Chuck

Infinitely adjustable, 0.5 up to 6.5 mm
Order number: DT-DC-6.5

Click picture for more information

Torque Pin Chuck

Infinitely adjustable, 0.5 up to 6.5 mm , stainless steel (V2A)
Order number: DT-DC-6.5SUS

Click picture for more information

Torque Pin Chuck

Infinitely adjustable, 0.5 up to 4 mm (for torque meters with 2 or 5 Nm nominal load).
Order number DT-DC-4

Click picture for more information

Torque Pin Chuck

Infinitely adjustable, 1.2 up to 13 mm (for torque meters with 5 or 10 Nm nominal load).
Order number: DT-DC-13

Click picture for more information

Upper Clamping Chuck

Clamping Chuck

for samples with from 20 up to 90 mm.
Includes table pins with urethane surface. It is recommended to use a torque wrench or torque driver to make the chucking force stable (4 mm hexagon bit is required). Recommended for screw caps, conductor plates, lens of cameras etc.
Order number: MT-TB

Click picture for more information

Clamping Chuck

for samples with from 7 up to 50 mm (for max. 5 Nm nominal load)
Includes table pins (ST-P) with urethane surface, length 10 mm. Recommended for locks, containers for eye drops, etc.
Order number: MT-ST

Click picture for more information

Clamping  Chuck

for samples with from 20 up to 50 mm (for max. 5 Nm nominal load).
Includes table pins (ST-01P) from stainless steel V2A, corrugated surface, length 10 mm.
Recommended for electronic components, plugs, etc.
Order number: MT-ST-01

Click picture for more information

Clamping  Chuck

for samples with from 7 up to 50 mm (for max. 5 Nm nominal load)
Includes table pins (ST-02P) with urethane surface, length 30 mm.
Recommended for cosmetics boxes, door knobs, lamps, etc.
Order number: MT-ST-02

Click picture for more information

Torque Pin Chuck

Infinitely adjustable, 0.5 up to 6.5 mm
Order number: MT-DC-6.5

Click picture for more information

Torque Pin Chuck

infinitely adjustable, 0.5 up to 6.5 mm , V2A
Order number: MT-DC-6.5SUS

Click picture for more information

Torque Pin Chuck

infinitely adjustable, 0.5 up to 4 mm
(for max. 5 Nm nominal load)
Order number: MT-DC-4

Click picture for more information

Torque Pin Chuck

infinitely adjustable, 1.2 up to 12 mm
(for torque meters with 5 or 10 Nm nominal load)
Order number: MT-DC-13

Click picture for more information

Adapter

With M10 male thread
Order number: MT-AD-M10

Click picture for more information

Standard Accessories

ZT Logger

USB cable approx. 1.5 m long, CD-ROM with USB-driver and software "ZT-Logger" for data transfer
AC Adapter

For 100 - 240 V AC
Order number: ADW-6010
Inspection Certificate

Delivery includes a manufacturers inspection certificate free of charge

Click picture for more information

Accessories optional

Force Recorder Light

Software for data aquisition by USB output
- Force-time graph
- Force gauge function setting
- Data storage as CSV file
Order number: SW-21
Force Recorder Standard

Additional functions in comparision to Force Recorder Light:
5 graphs at maximum can be displayed in a table
Order number: SW-22
Force Recorder Professional

Additional function in comparision to Force Recorder Light
- 5 graphs at maximum can be displayed i a table
- Force-angle graphing (possible only in combination with an angle meter)
Order number: SW-23
Printer

To print stored values using Mitutoyo Digimatic output.
Order number: DP-1 VR

Click picture for more information

Paper Roll

For Printer DP-1 VR, 1 Set = 5 pieces
Order number: DP-P
Table Pins

1 set (4 pieces), 25 mm long with urethane surface for the table.
Recommended for PET bottles, cans etc.
Order number: TB-P

Click picture for more information

Table Pins

1 set (4 pieces), 26 mm long from stainless steel for the table.
Recommended for aluminium cans, hard plastic containers etc.
Order number: TB-01P

Click picture for more information

Table Pins

1 set (4 pieces), 70 mm long with urethane surface for the table.
Recommended for conductor plates, lens of cameras, large bottles, etc.
Order number: TB-02P

Click picture for more information

Table Pin

1 set (4 pieces), 10 mm long with urethane surface for the small table.
Recommended for locks, containers for eye drops, etc.
Order number: ST-P

Click picture for more information

Table Pins

1 set (4 pieces), 10 mm long from stainless steel for the small table.
Recommended for electronic components, plugs, etc.
Order number: ST-01P

Click picture for more information

Table Pins

1 set (4 pieces), 30 mm long with urethane surface for the small table.
Recommended for cosmetics boxes, door knobs, lamps, etc.
Order number: ST-02P

Click picture for more information

Sample Stage

To get a flat working face on the table, for placing the sample.
1 set = 2 peaces
Order number: TB-SP

Click picture for more information

Extension Shaft

for lengthening the main shaft to clamp samples with lower height.
Length 100 mm
Order number: MT-EXT

Click picture for more information

Connecting Cable

For analog output, for connection to a line recorder.
Length approx. 3 m
Order number: CB-108
Connecting Cable

For RS 232 output with sub D 9 female, for connection to PC.
Length approx. 3 m
Order number: CB-208
Connecting Cable

For Mitutoyo Digimatic output, for connection to Mitutoyo printer DP-1 VR.
Length approx. 3 m
Order number: CB-308
Connecting Cable

with open ends (37-pin) for all available output signals to connect an unique device.
Order number: CB-908
Connecting Cable

for trigger input (input signal from an external device e. g. electronic switch to stop the measurement)
Order number: CB-808
Accumulator

Nickel metal hydride accumulator, 2-pole connector
3.6 V, 1300 mAh
Order number: DP-308

Click picture for more information

Calibration Certificate

Calibration certificate with calibration report is optional available.

Delivery Includes

Torque stand, torque meter, upper and lower clamping device, AC adapter, manufacturer`s inspection certificate, USB cable 1.5 m, CD-ROM with driver, simple software for communication and data logging ZT-Logger and operation instructions in english

Dimensions

Dimensions For PDF-file please
click picture

Specifications

Torque Stand
Sample Height:max. 140, 240 or340 mm
Speed:3 - 90 /s adjustable
Temperature range:0 - 40 C
Air humidity:80 % RH, max.
Power supply:100 - 240 V AC, 50/60 Hz, max. 3 A
Housing dimensions:See dimensions
Weight:14 kg net without accessories

Torque Meter
Accuracy:0.5 % full scale 1 digit
Measuring frequency:2000 times/s
Selectable units:Nm, kgfm, Lb.in oder Ncm, kgfcm, Lb.in
Display:OLED, 4 digit, 14 mm high
Overload protection:Approx. 200 % full scale
flashing display beyond 110 % full scale
Display update:10 times/s
Memory:Internal memory for max. 1000 values,
(clockwise or counter clockwise and peak values)
Setpoints:Min (-NG), Max (+NG) adjustable with output signal
Output signal:USB
RS 232 C (8, 1, N, 19200)
analog 2 V DC
Mitutoyo Digimatic
Open collector 4x (+NG, Ok, -NG, OVL), max. 30 V DC, 10 mA
overload signal
Temperature range:0 - 40 C
Air humidity:80 % RH max.
Power supply:Rechargeable NiMH battery pack (approx. 8 hours continous use)
and/or AC adapter 100 - 240 V AC with two adapters (EU/USA)
Housing dimensions:305 x 233 x 127 mm (LxWxH)
Weight, net (gross):Approx. 4900 g (Approx. 5900 g)

additional functions model DTXA in comparision to model DTXS
Memory:Readings can be transfered from the internal memory to an USB flash drive or direcly saved on it (sampling rate100 times/s)
High low output:2 high/low output values can be set. If the reading reaches one of the output values, data will be sent to external devices (e. g. PC, printer) for data recording
Extended peak mode:Indication of two peak values per measurement

additional functions model MTS-RA in combination with DTXA
Force displacement measurement:The Software Force Recorder Professional is required

Specifications subject to change without notice!

News

1209451075.jpg

New Tension Meter

1496124624.jpg

With one click you can download the information sheet for our new tension sensor.

Contact

Call us!

+49 (0)8638 9410-0
Can't find what you're looking for? Then get in touch with our experts.

Send us a fax!

+49 (0)8638 4825
You can also send us a fax with your message or request.

Contact via E-Mail!

info@hans-schmidt.com
Or feel free to email
us via our contact form!